All Issue

2017 Vol.49, Issue 3 Preview Page
Study on the Drive Parameters of a High-precision Basis Weight Control Valve
Bo Wang
,
Wei Tang1†
,
Jixian Dong
,
Feng Wang2
College of Bioresources Chemical and Materials Engineering of Shaanxi University of Science & Technology, Xi’an, Shaanxi Province, 710021
1Industrial Automation Institute of Shaanxi University of Science & Technology, Xi’an, Shaanxi Province, 710021
2Zhejiang Linuo Flow Control Technology Co., Ltd., Rui’an, Zhejiang, 325200
†Corresponding author: E-Mail: wtang906@163.com
30 June 2017. pp. 41-56
PDF XML Citation
Abstract

Decreasing precision or mechanical damage may occur in basis weight valves because of excess design torque valves. Stepping motor driver current values are set at the rated motor current or are based on practical experience. Applied technological research on current setting values was conducted in this paper. A current-setting experimental device was developed to solve this problem. The drive parameters include the drive current value, mechanical strength of valve actuator and the state holding current value were tested. Finally, the acceleration time for the trapezoidal velocity curve was calculated, which was helpful to improve the positioning precision of the valve. The test result with a sample diameter of a DN125 basis weight valve showed that the reasonable current value stage was 3.71 A, and the state holding current value stage was 50%. Then, the acceleration and deceleration times of the trapezoidal velocity curve were both set at 0.01 seconds. The positioning precision was able to match the requirements of a basis weight control valve for 10,000 steps in which an error of 1 step was less than 5.0% during 10,000 positioning steps under such drive parameters.

Keywords
Basis weight control valve
stepping motor driver
driving torque
drive current
trapezoidal velocity curve
References

Literature Cited

1
F. Hiroshi and M. Fumiharu, Yokogawa Technical Report English Edition, Control parameter optimization service for paper machine quality control systems, QCS tune-up engineering, for ideal paper manufacturing plant, 54(1); 61-64 (2011)

Hiroshi, F. and Fumiharu, M., Control parameter optimization service for paper machine quality control systems, QCS tune-up engineering, for ideal paper manufacturing plant, Yokogawa Technical Report English Edition 54(1):61-64 (2011).

2
K. Figiel, J. Gill, R. MacHattie, S. Nuyan, S. Sturm and J. Tippett, Measurement systems and product variability, Paper machine quality control systems (QCS)Paper Conference and Trade Show 2010, PaperCon 2010, Vol. 1, Pearson Education Limited, London; 266-320

Figiel, K., Gill, J., MacHattie, R., Nuyan, S., Sturm, S., and Tippett, J., Measurement systems and product variability, Paper machine quality control systems (QCS), Paper Conference and Trade Show 2010, PaperCon 2010, Vol. 1, Pearson Education Limited, London, pp. 266-320.

3
B. Wang, W. Tang, Q. L. Liu and X. Wang, China Pulp & Paper, Research and development of medium high-precision valve for basis weight control of paper machine, 33(3); 39-43 (2014)

Wang, B., Tang, W., Liu, Q. L., and Wang, X., Research and development of medium high-precision valve for basis weight control of paper machine, China Pulp & Paper 33(3):39-43 (2014).

4
B. Wang, W. Tang, Q. L. Liu and X. Wang, Fluid Machinery, Optimal design of medium high-precision quantitative valve for basis weight control of paper machine, 42(8); 52-55 (2014)

Wang, B., Tang, W., Liu, Q. L., and Wang, X., Optimal design of medium high-precision quantitative valve for basis weight control of paper machine, Fluid Machinery 42(8):52-55 (2014).

5
M. Bendjedia, Y. Ait-Amirat, B. Walther and A. Berthon, IEEE Transactions on Power Electronics, Position control of a sensorless stepper motor, 27(2); 578-587 (2012)

Bendjedia, M., Ait-Amirat, Y., Walther, B., and Berthon, A., Position control of a sensorless stepper motor, IEEE Transactions on Power Electronics 27(2):578-587 (2012).

10.1109/tpel.2011.2161774
6
N. T. Hegde, S. Meenatchisundaram and A. Vaz, International Journal of Engineering Trends and Technology, Modeling stepper motor control system with micro-stepping excitation mode, 2(1); 136-143 (2016)

Hegde, N. T., Meenatchisundaram, S., and Vaz A., Modeling stepper motor control system with micro-stepping excitation mode, International Journal of Engineering Trends and Technology 2(1):136-143 (2016).

7
B. G. Lipták and B. G. Liptak, 4th Edition. Instrument engineers' handbook: process control and optimizationInstrument Engineers' Handbook; 1106-1121, Vol. 2,, New York. CRC PressChilton Book Co. (20061982)

Lipták, B. G., Instrument engineers' handbook: process control and optimization, 4th Edition, Vol. 2, CRC Press, New York, pp. 1106-1121 (2006), Liptak, B. G. (1982), Instrument Engineers' Handbook, Chilton Book Co.

8
Valveproducts.metso.com, Metso Neles ACETM Basis weight control valve [online], Available at: http://valveproducts.metso.com/documents/ neles/TechnicalBulletins/en/8ACE21EN. pdf (2016)

Valveproducts.metso.com, Metso Neles ACETM Basis weight control valve [online], Available at: http://valveproducts.metso.com/documents/ neles/TechnicalBulletins/en/8ACE21EN. pdf [Accessed 20 June 2017] (2016)

9
Docin.com, VBW-1100 Basis Weight Valve [online], Available at: http://www.docin.com/ p-1083369025.html (2017)

Docin.com, VBW-1100 Basis Weight Valve [online], Available at: http://www.docin.com/ p-1083369025.html [Accessed 20 June 2017] (2017)

10
H. C. Mo, Small and special motor; 375, Peking, China. China Electric Power Press. (2015)

Mo, H. C., Small and special motor, China Electric Power Press, Peking, China, p. 375 (2015).

11
L. Zhou, S. H. Yang and X. D. Gao, Electric Machines & Control, Modeling of stepper motor control system and running curve simulation, 15(01); 20-25 (2011)

Zhou, L., Yang, S. H., and Gao, X. D., Modeling of stepper motor control system and running curve simulation, Electric Machines & Control 15(01):20-25 (2011).

12
H. Tom, Power Electronics Technology, Stepper motor controller/driver simplifies stepper motor system, 8(16); 24-27 (2010)

Tom, H., Stepper motor controller/driver simplifies stepper motor system, Power Electronics Technology 8(16):24-27 (2010).

13
S. Derammelaere, C. Debruyne, F. D. Belie and K. Stockman, Iet Electric Power Applications, Load angle estimation for two-phase hybrid stepping motors, 8(7); 257-266 (2014)

Derammelaere, S., Debruyne, C., Belie, F. D., and Stockman, K., Load angle estimation for two-phase hybrid stepping motors, Iet Electric Power Applications 8(7):257-266 (2014).

10.1049/iet-epa.2013.0333
14
R. Antonello, A. Cenedese and R. Oboe, IFAC Proceedings, Torque ripple minimization in hybrid stepper motors using acceleration measurements, 44(1); 10349-10354 (2011)

Antonello, R., Cenedese, A., and Oboe, R., Torque ripple minimization in hybrid stepper motors using acceleration measurements, IFAC Proceedings 44(1):10349-10354 (2011).

10.3182/20110828-6-it-1002.02022
15
W. Kim, D. Shin, Y. Lee and C. C. Chung, Mechatronics, Simplified torque modulated microstepping for position control of permanent magnet stepper motors, 35; 162-172 (2016)

Kim, W., Shin, D., Lee, Y., and Chung, C. C., Simplified torque modulated microstepping for position control of permanent magnet stepper motors, Mechatronics 35:162-172 (2016).

10.1016/j.mechatronics.2016.02.002
16
D. Zhe, X. S. Mei and M. X. Xu, Sensors, Modelling and analysis of a new piezoelectric dynamic balance regulator, 12(11); 14671-14691 (2012)

Zhe, D., Mei, X. S., and Xu, M. X., Modelling and analysis of a new piezoelectric dynamic balance regulator, Sensors 12(11):14671-14691 (2012).

17
F. Yu, M. Zhao, Y. Lin and Y. Huang, China Mechanical Engineering, Study on continuous test method of stepper motor torque-angle relationship, 25(3); 333-336 (2014)

Yu, F., Zhao, M., Lin, Y., and Huang, Y., Study on continuous test method of stepper motor torque-angle relationship, China Mechanical Engineering 25(3):333-336 (2014).

18
J. M. J. Villegas, C. A. Avizzano, E. Ruffaldi and M. Bergamasco, A low cost open-controller for interactive robotic system2015 IEEE European Modelling Symposium Conference, Modelling Symposium (EMS); 462-468

Villegas, J. M. J., Avizzano, C. A., Ruffaldi, E., and Bergamasco, M., A low cost open-controller for interactive robotic system, 2015 IEEE European Modelling Symposium Conference, Modelling Symposium (EMS), pp. 462-468.

10.1109/ems.2015.75
19
J. L. Liu, Y. Song and F. Liu, Aviation Precision Manufacturing Technology, Research of magnetic powder brake loading characteristic, 49(2); 56-60 (2013)

Liu, J. L., Song, Y., and Liu, F., Research of magnetic powder brake loading characteristic, Aviation Precision Manufacturing Technology 49(2):56-60 (2013).

20
P. W. Lu, The third edition. Practical valve design handbook; 1317, Peking, China. China Machine Press. (2012)

Lu, P. W., Practical valve design handbook, The third edition, China Machine Press, Peking, China, p. 1317 (2012).

21
P. J. Siripala and Y. A. Sekercioglu, Mechatronics, A generalised solution for generating stepper motor speed profiles in real time, 23(5); 541-547 (2013)

Siripala, P. J. and Sekercioglu, Y. A., A generalised solution for generating stepper motor speed profiles in real time, Mechatronics 23 (5):541-547 (2013).

10.1016/j.mechatronics.2013.04.004
22
S. Starin and C. Shea, Primer stepper motor nomenclature, definition, performance and recommended test methodsProceedings of the 42nd Aerospace Mechanisms Symposium, NASA Goddard Space Flight Center, Maryland; 375-390 (2014)

Starin, S. and Shea, C., Primer stepper motor nomenclature, definition, performance and recommended test methods, Proceedings of the 42nd Aerospace Mechanisms Symposium, NASA Goddard Space Flight Center, Greenbelt, Maryland, pp. 375-390 (2014).

23
A. Hughes and B. Drury, The 4th edition. Electric motors and drives: fundamentals, types and applications; 24-29, Oxford, UK. Newnes. (2013)

Hughes, A. and Drury, B., Electric motors and drives: fundamentals, types and applications. The 4th edition, Newnes, Oxford, UK, pp. 24- 29 (2013).

24
D. X. Cheng, The sixth edition. Handbook of mechanical design, Vol. 1; 104-109, Peking, China. Chemical Industry Press. (2016)

Cheng, D. X., Handbook of mechanical design, Vol. 1, The sixth edition, Chemical Industry Press, Peking, China, pp. 104-109 (2016).

25
B. Wang, W. Tang, J. X. Dong and F. Wang, Paper and Biomaterials, Positioning-control based on trapezoidal velocity curve for high-precision basis weight control valve, 2(2); 42-50 (2017)

Wang, B., Tang, W., Dong, J. X., and Wang, F., Positioning-control based on trapezoidal velocity curve for high-precision basis weight control valve. Paper and Biomaterials 2(2): 42-50 (2017).

Information
  • Publisher :Korea Technical Association of The Pulp and Paper Industry
  • Publisher(Ko) :한국펄프종이공학회
  • Journal Title :Journal of Korea TAPPI
  • Journal Title(Ko) :펄프종이기술
  • Volume : 49
  • No :3
  • Pages :41-56
  • Received Date : 2017-02-21
  • Revised Date : 2017-06-18
  • Accepted Date : 2017-06-20
  • DOI :https://doi.org/10.7584/JKTAPPI.2017.06.49.3.41
Journal Informaiton Journal of Korea TAPPI Journal of Korea TAPPI
Online Submission
  • scopus
  • NRF
  • KOFST
  • crossref crossmark
  • crossref cited-by
  • crosscheck
  • orcid
Journal Informaiton Journal Informaiton - close