All Issue

2021 Vol.53, Issue 2 Preview Page
Application of Organic and Inorganic Additive Addition for Linerboard Drying Energy Reduction

라이너지 건조 에너지 저감을 위한 유기 및 무기 첨가제의 적용

Min Woo Lee12
,
Yung Bum Seo3†
이민우 12
,
서영범 3†
1Department of Biobased Materials, College of Agriculture and Life Sciences, Chungnam National University
2Hansol Paper Co. Ltd., R&D Center
3Department of Biobased Materials, College of Agriculture and Life Sciences, Chungnam National University
1충남대학교 농업생명과학대학 환경소재공학과, 학생
2한솔제지 중앙연구소, 책임연구원
3충남대학교 농업생명과학대학 환경소재공학과, 교수
†Corresponding author: E-Mail: ybseo@cun.ac.kr (Address: Department of Biobased Materials, College of Agriculture and Life Sciences, Chungnam National University, Daejeon, 34134, Republic of Korea)
30 April 2021. pp. 32-39
PDF XML Citation
Abstract

Linerboard needs high compressive strength for manufacturing high performance corrugated board, inexpensive raw materials for lowering manufacturing cost, and high solid content after wet pressing for drying energy savings. Ground calcium carbonate (GCC) is the least expensive papermaking raw material until now. However, addition of GCC to linerboard raw stock always lowers hydrogen bonding between wood fibers and thereby, lowers strength properties. We investigated the combined effect of large size calcium carbonate addition and high wet pressing pressure application on the properties of linerboard. The large size GCC, aragonite type precipitated calcium carbonate (PCC) and the fibers from medium density fiberboard (MDF) were used in the study. The smaller the size of GCC, the higher the solid content after pressing and the lower the strength properties of linerboard. Aragonite type calcium carbonate increased solid content and kept compressive strength. MDF fibers was only effective on increasing bulk. Further investigation of the aragonite calcium carbonate is recommended for elucidating its full potential for both lowering production cost and drying energy saving of linerboard production.

Keywords
Linerboard
compressive strength
solid content
calcium carbonate
aragonite
drying energy saving
References

Literature Cited

1

Sung, Y. J., Kim, D. S., Um, G. J., Lee, J. W., Kim, S.B., and Park, G. S., Action plans of paper industry correspond to the carbon dioxide emission trading market, Journal of Korea TAPPI 4(1):43-51 (2012).

10.7584/ktappi.2012.44.1.043
2

Chudnovsky, Y., Innovative gas-fired technology for paper drying, Spring Technical & International Environmental Conference, 2004 Paper Summit, p. 70-73 (2004).

3

Jeong, Y. B., Lee, H. L., Jeong, K. H., and Ryu, H., Influence of the viscosity of surface sizing starch solutions on surface sizing effect of linerboard, Journal of Korea TAPPI 4(5):54-62 (2012).

10.7584/ktappi.2012.44.5.054
4

Kaapa, O., The optimization of press dewatering and its influence on energy savings, 2008 PAPERCON Conference, pp. 253-257 (2008).

5

Pickin, J. G., Yuen, S. T. S., and Henings, H., Waste management options to reduce greenhouse gas emissions from paper in Australia, Atmospheric Environment 36:741-752 (2002).

10.1016/S1352-2310(01)00532-5
6

Skalicky, C. and Milchovsky, M., Dehydration behavior of pulp during pressing, Cellulose Chemistry and Technology 26(1):85-98 (1992).

7

Seo, D. J., Overviews on energy savings in paper industry, 2009 KTAPPI Colloquium, p. 47-67 (2009).

8

Paulapuro, H., Chapter 8. Wet pressing In Papermaking Science and Technology, Papermaking Part1, Stock preparation and wet end, Fapet Oy, Finland, p. 287 (2000).

9

Springer, A., Nabors, L. A., and Bhatia, O., The influence of fiber, sheet structural properties, and chemical additives on wet pressing, TAPPI J. 74(4):21-28 (1991).

10

Sung, Y. J., Lee, B. R., Jeong, W. K., Jung J. G., Choi S. G., Im C. K., Gwon W. O., and Seo Y. B., Changes in wet pressing response of OCC stock by the beating time and the addition of polymer aids, Journal of Korea TAPPI 43(2):7-82 (2012).

11

Sung, Y. J., Jeong, W. K., Kim, D. S., Oh, M. T., Hong, H. U., Seo, Y. B., Im, C. K., Gwon, W. O., and Kim, J.D., Evaluation of wet pressing response of recycled OCC with roll press simulator, Journal of Korea TAPPI 4(4):85-90 (2012).

10.7584/ktappi.2012.44.4.085
12

Jeong, W. K. and Sung, Y. J., Wet pressing properties of OCC stock depending on the fines contents, Journal of Korea TAPPI 4(6):21-27 (2012).

10.7584/ktappi.2012.44.6.021
13

Hwang, I. Y., Lee, Y. H., Jung, J. G., Sung Y. J., and Seo Y. B., Application of spacers for increasing OCC solid content in wet pressing process (I), Journal of Korea TAPPI 4(4):2-7 (2012).

10.7584/ktappi.2012.44.4.001
14

Lee, J. Y., Lee, E. K., Sung, Y. J., Kim, C. H., Choi, J. S., Kim, B. H., Lim, G. B., and Kim J, S., Application of new powdered additives to paperboard using peanut husk and garlic stem, Journal of Korea TAPPI 43(4):40-48 (2011).

15

Kim, C. H., Lee, J. Y., Lee, Y. R., Chung, H. K., Back, K. K., Lee, H. J., Gwak, H. J., Gang, H. R., and Kim, S. H., Fundamental study on developing lignocellulosic fillers for papermaking (Ⅱ), Journal of Korea TAPPI 41(2):1-6 (2009).

16

Chae, H. J. and Park, J. M., Study on drainage and physical properties of KOCC handsheet containing pretreated wooden fillers, Journal of Korea TAPPI 43(3):21-29 (2011).

17

Lee, J. Y., Kim, C. H., Choi, J. S., Kim, B. H., Lim, G. B., and Kim, D. M., Development of new powdered additive and its application for improving the paperboard bulk and reducing drying energy (Ⅰ), Journal of Korea TAPPI 4(2):58-6 (2012).

10.7584/ktappi.2012.44.2.058
18

Lee, J. Y., Kim, C. H., Choi, J. S., Kim, B. H., Lim, G. B., and Kim, S. Y., Effect of new organic filler on physical properties and drying energy consumption of paperboard, Proceeding of Fall Conference of the KTAPPI, p. 29-36 (2012).

19

Bown, R., Particle size and structure of paper filler-sand their effect on paper properties, Paper Technology 39(2):4-48 (1998).

20

Hube, M., Pawlak, J., and Koukoulas, A., Paper's appearance: A review, Bioresources 3(2):627-65 (2008).

10.15376/biores.3.2.627-665
21

Han, Y. R. and Seo, Y. B., Effect of particle shape and size of calcium carbonate on physical properties of paper, Journal of Korea TAPPI 29(1):7-15 (1997).

22

Hwang, I. Y., Ji, S. G., and Seo, Y. B., Use of calcium carbonate for improving solid content of KOCC wet web, Journal of Korea TAPPI 45(6):1-9 (2013).

10.7584/ktappi.2013.45.6.001
23

Ramakrishna, C., Thenepalli, T., Huh, J. H., and Ahn, J. H., Preparation of needle like aragonite precipitated calcium carbonate (PCC) from dolomite by carbonation method, Journal of the Korean Ceramic Society 53(1):7-12 (2016).

10.4191/kcers.2016.53.1.7
Information
  • Publisher :Korea Technical Association of The Pulp and Paper Industry
  • Publisher(Ko) :한국펄프종이공학회
  • Journal Title :Journal of Korea TAPPI
  • Journal Title(Ko) :펄프종이기술
  • Volume : 53
  • No :2
  • Pages :32-39
  • Received Date : 2021-02-19
  • Revised Date : 2021-04-05
  • Accepted Date : 2021-04-16
  • DOI :https://doi.org/10.7584/JKTAPPI.2021.04.53.2.32
Journal Informaiton Journal of Korea TAPPI Journal of Korea TAPPI
Online Submission
  • scopus
  • NRF
  • KOFST
  • crossref crossmark
  • crossref cited-by
  • crosscheck
  • orcid
Journal Informaiton Journal Informaiton - close