All Issue

2021 Vol.53, Issue 6 Preview Page
Dry Grinding Efficiency of Zeolite According to the Manipulated Variable

조작 변수에 따른 도공용 제올라이트의 건식분쇄 효율성

Min-Je Kim1
,
Yong-Kyu Lee2†
김민제 1
,
이용규 2†
1Department of paper Science & Engineering, College of Forest & Environmental Sciences, Kangwon National University
2Department of paper Science & Engineering, College of Forest & Environmental Sciences, Kangwon National University
1강원대학교 산림환경과학대학 제지공학과, 대학원생
2강원대학교 산림환경과학대학 제지공학과, 교수
†Corresponding author: E-Mail: yklee@kangwon.ac.kr (Address: Department of paper Science & Engineering, College of Forest & Environmental Sciences, Kangwon National University, 24341, Republic of Korea)
30 December 2021. pp. 106-112
PDF XML Citation
Abstract

Silica has been used as the main pigment for inkjet paper. Silica has a problem of fluidity and is expensive because it is not produced in Korea. Therefore, research on replacing silica with zeolite was conducted. The zeolite pulverized for coating is not commercially available. In order to modify zeolite to special pigment for inkjet coating, this study conducted to optimize the zeolite the zeolite grinding process by a ball mill for the best grinding efficiency. A traditional ball mill and a planetary ball mill were utilized. Two different balls with a dimeter of 10 mm and 15 mm were used. Effects of the mixing ratio of the two different balls, the speed of a ball mill, and grinding time were investigated in terms of grinding efficiency. The grinding efficiency was evaluated by measuring the weight of the zeolite passing through 100 mesh and 140 mesh wire, respectively. It was found that the best grinding efficiency was obtained when mixing 75% of 15 mm balls and 25% of 10 mm balls.

Keywords
Zeolite
silica
traditional ball mill
planetary ball mill
efficiency
References

Literature Cited

1

Ozcan. A. and Tutak. D., The effect of zeolite on inkjet coated paper surface properties and deinking, Nordic Pulp & Paper Research Journal 35(3):432-439 (2020).

10.1515/npprj-2020-0025
2

Lamminmäki, T., Kenttä, E., Rautkoski, H., Bachér, J., Teir, S., Kettle, J., and Sarlin, J., New silica coating pigment for inkjet papers from mining industry sidestreams, Journal of Surface Engineered Materials and Advanced technology 3(3):224-234 (2013).

10.4236/jsemat.2013.33030
3

Lee, H. R., Lee, S. G., Yoon, H. J., Han, J. S., Oh, W. D., Choi, H. Y., and Lee, D. H., A Study on the Improvement of Binder System for inkjet coating collar and inkjet paper, 219-226 (2007).

4

Rimola, A., Costa, D., Sodupe, M., Lambert, J., and Ugliengo, P., Silica surface features and their role in the adsorption of biomolecules: Computational modeling and experiments, Chemical Reviews 113(6):4216-4313 (2013).

10.1021/cr3003054
5

Im, G., Characteristics of zeolites, Natural Science Paper Collection: Baejae University Advanced Science Research Institute Natural Science Paper Collection: Baejae University Advanced Science Research Institute Vol. 6, No. 1 (1993).

6

Lee S. A., Han H. K., Comminution of alumina using ball mill, Journal of the Korea Academia-Industrial cooperation Society 22(8):688-694 (2021).

10.5762/KAIS.2021.22.8.688
7

Tamaki, S., Hisamatsu, M., Teranishi, K., Adachi, T., and Yamada, T, Structural change of maize starch granules by ball mill treatment, Starch Stärke 50(8):342-348 (1998).

10.1002/(SICI)1521-379X(199808)50:8<342::AID-STAR342>3.0.CO;2-B
8

Abdellaoui, M. and E. Gaffet. The physics of mechanical alloying in a planetary ball mill: mathematical treatment, Acta Metallurgica et Materialia 43.3:1087-1098 (1995).

10.1016/0956-7151(95)92625-7
9

Choi J. Y.,and Kim S. J., A mixing ratio Optimization of ball mills using design of experiments with mixture, The Korean Operations Research and Management Science Society, 1369-1374 (2011).

10

Mio, H., Kano, J., and Saito, F., Scale-up method of planetary ball mill, Chemical Engineering Science 59(24):5909-5916 (2004).

10.1016/j.ces.2004.07.020
11

Kotake, N., Suzuki, K., Asahi, S., and Kanda, Y., Experimental study on the grinding rate constant of solid materials in a ball mill, Powder Technology 122(2-3):101-108 (2002).

10.1016/S0032-5910(01)00405-3
12

Bor, A., Jargalsaikhan, B., Lee, J., and Choi, H., A comparative study for grinding media behavior and dem simulation at actual grinding zone on a traditional ball mill, Korean Chemical Engineering Research 57(6):804-811 (2019).

13

Kotake, N., Kuboki, M., Kiya, S., and Kanda, Y., Influence of dry and wet grinding conditions on fineness and shape of particle size distribution of product in a ball mill, Advanced Powder Technology 22(1):86-92 (2011).

10.1016/j.apt.2010.03.015
14

Le Brun, P., Gaffet, E., Froyen, L., and Delaey, L., Structure and properties of Cu, Ni and Fe powders milled in a planetary ball mill, Scr. Metall. Mater 26:1743-1748 (1992).

10.1016/0956-716X(92)90545-P
15

Zhang, J., Bai, Y., Dong, H., Wu, Q., and Ye, X., Influence of ball size distribution on grinding effect in horizontal planetary ball mill, Advanced Powder Technology 25(3):983-990 (2014).

10.1016/j.apt.2014.01.018
Information
  • Publisher :Korea Technical Association of The Pulp and Paper Industry
  • Publisher(Ko) :한국펄프종이공학회
  • Journal Title :Journal of Korea TAPPI
  • Journal Title(Ko) :펄프종이기술
  • Volume : 53
  • No :6
  • Pages :106-112
  • Received Date : 2021-12-06
  • Revised Date : 2021-12-24
  • Accepted Date : 2021-12-27
  • DOI :https://doi.org/10.7584/JKTAPPI.2021.12.53.6.106
Journal Informaiton Journal of Korea TAPPI Journal of Korea TAPPI
Online Submission
  • scopus
  • NRF
  • KOFST
  • crossref crossmark
  • crossref cited-by
  • crosscheck
  • orcid
Journal Informaiton Journal Informaiton - close